Contact Imprint Terms and Conditions
Logo GloCon Head Collage
  deutsch | english | Русский Print this site!
Home
News
Beratumg
Investment Advice and Technology Consulting
Produkte
Injection Moulding Machines / Complete Production Systems for Preforms and Closures
PET-Stretchblow Moulding Machines /complete Bottle Production Systems
Beverage and Foods Factory Planning
Auxiliary Equipment
Unternehmen
About GloCon
Service
Downloads
Contact
Imprint
High Pressure Compressor Plants to provide PET-Stretchblow Systems with oilfree blow air.
Foto
Photo
HATLAPA-High pressure compressor with high efficiency filtration for oilfree blow air supply for low capacity requirements of up to 220 Nm3/h  or plus 220 = 440 Nm3/h [base frame, refrigirator dryer and pressure accumulator vessels laid out for tandem].
Foto
High Pressure Compressor Plant for the supply of oilfree blow air - manufactured/"packaged" by SIAD - for medium capacity requirements of up to 600 Nm3/h.
Foto
BELLISS&MORCOM-High Pressure Piston Compressor Plant for the supply of oilfree blow air for PET-bottles - suitable for medium-to-higher capacity requirements of up to 1.200 Nm3/h.
Foto
ABC-High Pressure Compressor Plant for the supply of oilfree blow air - suitable for medium-to-higher capacity requirements of up to 1.200 Nm3/h.
Foto
ATLAS-COPCO-High Pressure Compressor Plant (screw compressor ZR3 + Booster 40D3) for the supply of oilfree blow air - for high capacity requirements of up to 1.927 Nm3/h.
Under consideration of product-, project and environmental data GloCon sizes these "sub-plants" and generally supplies them as part of a systems package up to the bottling line … incl. the empty- bottle-air conveyor transport to the rinser/filler.
Photo
B - Process support aggregates for injection moulding of preforms:
The resin drier dries the highly hygroscopic resin granules. The sufficiently dried material is an essential pre-requisite for a preform of impeccable quality with dimensional consistency which can be properly stretchblown. As a rule a drying time of 4-6 hours must precede the actual fluxing, plasticizing and injection of the material.
Even more than for blow moulding the sufficient cooling function is essential : one of the two cooling circuits provides the cooling for the drier, the hydraulic system of the machine and the cabinet - this would be a 20°C- circuit; the second circuit would provide the cooling effect for the mould, the takeout robot and - should the site of operation not be air conditioned - to the dehumidifying device. It is the mould which absorbs large volumes of clean 6°C-water for it to operate at short cycle times (= high productivity).

In order to prevent water from condensing in the cavities and on the cores resulting from the effect of the dry cold air it is imperative to either air condition the operating environment of the mould or to sue a dehumidifying cell instead.

For this purpose GloCon would install a dehumidifier unit. By way of a pipeline the humid air will be evacuated from the mould and preform takeout robot area.

Based on project and environmetal data GloCon sizes these machines and devices and usually supplies them as part of the systems package.
14.000 bph

LANFRANCHI-PET-Bottle-Unscrambler, model L2-SR-14, built in 1999, only 2.500 hours (lab operation), tested for up to 14.000 bph, *set up* for bottles with 38 *mm-neck finish* - can be changed over optionally to PCO28 or other neck finishes with a few weeks (parts sourcing).
Abstand Photo
Click on the picture for enlargement

Abstand Photo
Click on the picture for enlargement
top
  GloCon Technical Supplies & Trading GmbH | Werkstrasse 112 | D-19061 Schwerin |Phone +49 (0)385-636 442-0 | Fax +49 (0)385-636 442-19